近排批量修诺基亚N1202机，刷机失败，出现的英文提示，有以下几种显示，应是告诉刷机失败的原因及维修思路的，因本人英语水平不高，求英语水平好的，翻译出来，这样的话，对维修有极大的帮助，麻烦高手了。谢谢！
一、
Booting phone...
Phone didn't answer with TX line low after UEM reset!
Causes:
1. put a 27-33 pico capacitor in connector b/w mbus-gnd.
2. UEM damaged -> replace uem.
MCU ID: 0xDDDD
This MCU ID is not supported in chosen flash file...
Error booting phone...
二、
Booting phone...
Phone didn't answer to request flash routine!
Causes:
1. UPP damaged -> replace UPP
MCU ID: 0xEEEE
This MCU ID is not supported in chosen flash file...
Error booting phone...
三、Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: B61AAC7E <=> Flash ID not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 0
FLASH ID1: 13C1EBD2 <=> Flash ID not in database Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: 02 7E AC 1A B6 1A B6 1A B6 1A B6 1A B6 1A B6 1A
Flash ID is 0x1AB67EAC
Cannot find flash loader for this phone...Aborting!
Error Loading loader!
四、
Booting phone...
MCU ID: 0xFFFF
This MCU ID is not supported in chosen flash file...
Error booting phone...
五、
Booting phone...
Phone didn't answer with TX line high after power on!
Causes:
1. Phone don't power on -> Check cable
2. TX pin from phone don't make contact -> Check cable
3. UPP damaged -> change UPP
MCU ID: 0xAAAA
This MCU ID is not supported in chosen flash file...
Error booting phone...
六、
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...
七、
Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: 00200020 <=> ST -> Type not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 0
FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 20
Flash ID is 0x20002000
Cannot find flash loader for this phone...Aborting!
Error Loading loader!
八、
Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
Error in CHK...
Error Loading loader!
九、
Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: 88280020 <=> ST -> Type not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 10
FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: AD 7E B6 1A 23 10 03 40 C6 05 E4 01 20 A2 65 14
Flash ID is 0x28882000
Flash loader is C:\Program Files\ODEON\JAF\Flash\u3_st_i.fia
Loader version: 04.46.01 -> Revision: 0007
Loader size is 0x4B38; Loader chk: df
Loader is ready...
P-key nokia module version 01.02
MSID: 8420D3A1BCE62110ABFE9928F3
MSID decoded: +
FAID: 549A27BFE5454A3320AFA663000000000000000000000000
Operation took 0 minutes 8 seconds...
Erasing...
Found 5 interval(s) to erase
Erasing area: 01000000 - 0100FFFF...
Erasing area: 01010000 - 013AFFFF...
Erasing area: 013B0000 - 013EFFFF...
Erasing area: 017C0000 - 017EFFFF...
Erasing area: 01FC0000 - 01FEFFFF...
Operation took 1 minutes 9 seconds...
Writing...
Error cmd: 14!
Addr: 01000064
一、
Booting phone...
Phone didn't answer with TX line low after UEM reset!
Causes:
1. put a 27-33 pico capacitor in connector b/w mbus-gnd.
2. UEM damaged -> replace uem.
MCU ID: 0xDDDD
This MCU ID is not supported in chosen flash file...
Error booting phone...
二、
Booting phone...
Phone didn't answer to request flash routine!
Causes:
1. UPP damaged -> replace UPP
MCU ID: 0xEEEE
This MCU ID is not supported in chosen flash file...
Error booting phone...
三、Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: B61AAC7E <=> Flash ID not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 0
FLASH ID1: 13C1EBD2 <=> Flash ID not in database Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: 02 7E AC 1A B6 1A B6 1A B6 1A B6 1A B6 1A B6 1A
Flash ID is 0x1AB67EAC
Cannot find flash loader for this phone...Aborting!
Error Loading loader!
四、
Booting phone...
MCU ID: 0xFFFF
This MCU ID is not supported in chosen flash file...
Error booting phone...
五、
Booting phone...
Phone didn't answer with TX line high after power on!
Causes:
1. Phone don't power on -> Check cable
2. TX pin from phone don't make contact -> Check cable
3. UPP damaged -> change UPP
MCU ID: 0xAAAA
This MCU ID is not supported in chosen flash file...
Error booting phone...
六、
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...
七、
Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: 00200020 <=> ST -> Type not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 0
FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: 00 20 00 20 00 20 00 20 00 20 00 20 00 20 00 20
Flash ID is 0x20002000
Cannot find flash loader for this phone...Aborting!
Error Loading loader!
八、
Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
Error in CHK...
Error Loading loader!
九、
Booting phone...
MCU ID: 0x2293
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: 88280020 <=> ST -> Type not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 10
FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: AD 7E B6 1A 23 10 03 40 C6 05 E4 01 20 A2 65 14
Flash ID is 0x28882000
Flash loader is C:\Program Files\ODEON\JAF\Flash\u3_st_i.fia
Loader version: 04.46.01 -> Revision: 0007
Loader size is 0x4B38; Loader chk: df
Loader is ready...
P-key nokia module version 01.02
MSID: 8420D3A1BCE62110ABFE9928F3
MSID decoded: +
FAID: 549A27BFE5454A3320AFA663000000000000000000000000
Operation took 0 minutes 8 seconds...
Erasing...
Found 5 interval(s) to erase
Erasing area: 01000000 - 0100FFFF...
Erasing area: 01010000 - 013AFFFF...
Erasing area: 013B0000 - 013EFFFF...
Erasing area: 017C0000 - 017EFFFF...
Erasing area: 01FC0000 - 01FEFFFF...
Operation took 1 minutes 9 seconds...
Writing...
Error cmd: 14!
Addr: 01000064