原文来自 http://user.qzone.qq.com/462639982/blog/3
最近总有人问解M1000网络锁的事,在此特整理一下解M1000的一些步承聚....
需要的设备 smart-clip,PC,and M1000 data cable
Unlock procedure for M1000
Models with boot versions up to 0.6.1.2 could be unlocked simply by pressing "Unlock" button on Smart-Clip (standard unlock procedure for P2K models).
M1000 (boot version 0.6.1.2) needs to be unlocked via Remove RSA option
1. Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
2. Connect S-Card to PC USB port.
3. Connect power supply to Smart-Clip and power on the handset.
4. Launch SmartMoto.
5. Choose "Smart-Clip USB port" in phone connection window.
6. Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads all information.
7. Log to bookmark "Unlock".
8. Pickup correct model from the scrolling list.
9. Press Remove RSA.
10. Phone enters boot mode, message "Waiting" appears on the bottom of phone display.
11. Press 1 and 2 buttons simultaneously in upper part of the handset and SmartMoto will continue the process.
12. Program will show a popup window with procedure description to be followed:
Remove phone battery;
Ensure that USB cable is plugged into the phone;
Press phone buttons 1 and 2 simultaneously;
While holding button 1 and button 2, insert battery;
Release buttons 1 and 2;
Message "Waiting" should appear on the bottom of phone display;
Press and release phone buttons 1 and 2 simultaneously once more;
Message "Waiting" should disappear, press 'OK' to continue.
13. SmartMoto finishes removing RSA, the handset turns ON.
14. Now phone requires being unlocked with Unlock button of Smart-Clip.
15. Connect the phone to the powered Clip.
16. Press UNLOCK button on the Clip.
17. Phone reloads. Within 5-10 seconds message "Waiting" appears on the bottom of the phone display.
18. Press 1 and 2 buttons simultaneously in upper part of the handset. Message "Waiting" disappears, phone enters boot mode (if you don't press these 2 keys during message "Waiting" is displayed, the clip will give red E/G led and you will have to start with step 15 again).
19. After 1 and 2 buttons have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on. Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
20. Green E/G led glows.
21. The cell phone is unlocked.
M1000 variants with higher boot versions will require TestPoint procedure to be unlocked.
Please be aware that TP procedure and data cable for M1000 differ from those for other P2K models.
TestPoint unlock procedure for M1000
1. Disassemble the phone.
2. Connect phone PCB to PC via Smart-Clip (phone > USB cable (not repair one)> Smart-Clip > LPT cable > PC).
3. Connect S-Card to PC USB port.
4. Connect power supply to Smart-Clip and power on the handset.
5. Launch SmartMoto.
6. Choose "Smart-Clip USB port" in phone connection window.
7. Connect TestPoint A to TestPoint B.
8. Press Button 1 and Button 2 simultaneously.
9. While holding Button 1 and Button 2 insert battery.
10. Release Button 1 and Button 2 for 1 second.
11. Press and release again Button 1 and Button 2 simultaneously.
12. Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset as "S Blank Neptune LTE", "S Blank"Paragon POG" or "S Blank Rainbow POG".
13. Disconnect TestPoint.
14. Log to bookmark "Unlock".
15. Select a correct model from the scrolling list.
16. Press "Unlock via TestPoint".
17. Disconnect PCB after the process is completed.
18. Assemble the phone.
Please note:
During TestPoint unlocking procedure phone's LCD must be disconnected.
Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
Use any other alternative tool to cut or drill it. Please make sure you do not damage the board
We strictly recommend to make a backup of flash from the handset before performing any procedure. This will enable you to restore the handset to its original state in case of unlock process failure.
以上办法都解决不了的就只好换掉128L18B字库了,该操作只能为专业三级维修技师完成
最近总有人问解M1000网络锁的事,在此特整理一下解M1000的一些步承聚....
需要的设备 smart-clip,PC,and M1000 data cable
Unlock procedure for M1000
Models with boot versions up to 0.6.1.2 could be unlocked simply by pressing "Unlock" button on Smart-Clip (standard unlock procedure for P2K models).
M1000 (boot version 0.6.1.2) needs to be unlocked via Remove RSA option
1. Connect handset to PC via Smart-Clip (phone > USB cable > Smart-Clip > LPT cable > PC).
2. Connect S-Card to PC USB port.
3. Connect power supply to Smart-Clip and power on the handset.
4. Launch SmartMoto.
5. Choose "Smart-Clip USB port" in phone connection window.
6. Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset and reads all information.
7. Log to bookmark "Unlock".
8. Pickup correct model from the scrolling list.
9. Press Remove RSA.
10. Phone enters boot mode, message "Waiting" appears on the bottom of phone display.
11. Press 1 and 2 buttons simultaneously in upper part of the handset and SmartMoto will continue the process.
12. Program will show a popup window with procedure description to be followed:
Remove phone battery;
Ensure that USB cable is plugged into the phone;
Press phone buttons 1 and 2 simultaneously;
While holding button 1 and button 2, insert battery;
Release buttons 1 and 2;
Message "Waiting" should appear on the bottom of phone display;
Press and release phone buttons 1 and 2 simultaneously once more;
Message "Waiting" should disappear, press 'OK' to continue.
13. SmartMoto finishes removing RSA, the handset turns ON.
14. Now phone requires being unlocked with Unlock button of Smart-Clip.
15. Connect the phone to the powered Clip.
16. Press UNLOCK button on the Clip.
17. Phone reloads. Within 5-10 seconds message "Waiting" appears on the bottom of the phone display.
18. Press 1 and 2 buttons simultaneously in upper part of the handset. Message "Waiting" disappears, phone enters boot mode (if you don't press these 2 keys during message "Waiting" is displayed, the clip will give red E/G led and you will have to start with step 15 again).
19. After 1 and 2 buttons have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on. Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
20. Green E/G led glows.
21. The cell phone is unlocked.
M1000 variants with higher boot versions will require TestPoint procedure to be unlocked.
Please be aware that TP procedure and data cable for M1000 differ from those for other P2K models.
TestPoint unlock procedure for M1000
1. Disassemble the phone.
2. Connect phone PCB to PC via Smart-Clip (phone > USB cable (not repair one)> Smart-Clip > LPT cable > PC).
3. Connect S-Card to PC USB port.
4. Connect power supply to Smart-Clip and power on the handset.
5. Launch SmartMoto.
6. Choose "Smart-Clip USB port" in phone connection window.
7. Connect TestPoint A to TestPoint B.
8. Press Button 1 and Button 2 simultaneously.
9. While holding Button 1 and Button 2 insert battery.
10. Release Button 1 and Button 2 for 1 second.
11. Press and release again Button 1 and Button 2 simultaneously.
12. Press "Search". Software should perform the following steps:
SmartMoto detects S-Card;
SmartMoto detects Smart-Clip;
SmartMoto detects the handset as "S Blank Neptune LTE", "S Blank"Paragon POG" or "S Blank Rainbow POG".
13. Disconnect TestPoint.
14. Log to bookmark "Unlock".
15. Select a correct model from the scrolling list.
16. Press "Unlock via TestPoint".
17. Disconnect PCB after the process is completed.
18. Assemble the phone.
Please note:
During TestPoint unlocking procedure phone's LCD must be disconnected.
Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
Use any other alternative tool to cut or drill it. Please make sure you do not damage the board
We strictly recommend to make a backup of flash from the handset before performing any procedure. This will enable you to restore the handset to its original state in case of unlock process failure.
以上办法都解决不了的就只好换掉128L18B字库了,该操作只能为专业三级维修技师完成